FG Falcon Brake Repair Toronto. A front disc disc machine was required and new Bendix GCT disc pads fitted for as new brakes again.

This is the result of ignoring the warning signs a vehicle gives you when your brakes are worn out. Metal on metal is obviously dangerous and complete brake failure can occur! Fortunately no further damage was caused and the Range Rover Sport required a rear brake replacement which consisted of new quality rear Disc Pads, Sensors, Disc Rotors, hand brake service and brake faults cleared on the vehicles computer. Belmont NSW. 

New caravan brakes fitted Edgeworth. The customer had complained of the brakes holding since he had purchased the van and had been unable to rectify the issue, so upon inspection found the incorrect brake shoes were fitted at some point and hadn't been identified. So Newcastle Mobile Brake Specialists sourced, fitted and serviced the correct replacement brake assembly for as new brakes again!

Newcastle Mobile Brake Repairs did some On Car Disc Machining today on a 200 Series Toyota Landcruiser which is common place on most 4wd's as they don't have floating disc rotors and are therefore labour intensive to swap out when warped or worn out. I can do this service for a fraction of the cost. I replaced the front disc pads with Bendix 4wd's which will give it that factory feel again also.

The Hyundai Santa Fe required a rear brake disc machine, new rear disc pads, a hand brake adjustment and a new hand brake cable for as new rear brake again. Belmont Newcastle NSW.

The SSV Redline had just ticked over 65000km and due for some rear brakes. I fitted a cleaner pad than the genuine Brembo's at an attempt to keep the wheels clean which was a success when fitted to the front recently. New RDA rotors were installed aswell.

On-Car Disc Rotor Machining.

Front brake disc rotor machining was carried out including new Bendix 4wd disc pads were fitted also at Belmont for as new brakes again on the Toyota Prado.

Front brake repair for the Toyota Corolla. It had a brake pulsation which typically transfers through to the brake pedal or steering wheel, so a little off putting when braking. This usually presents when the brakes are almost worn out and is either repaired by machining or replacing the brake disc rotors and brake disc pads, for as new brakes again. Brake repair Charlestown, Newcastle. 

Mobile Caravan Brake Repairs Newcastle. This one was carried out at Elermore Vale in the customers driveway. It required a full brake service, lubrication, repack and adjust wheel bearings.

The front brakes were worn out on the Toyota Hilux at Belmont so new DBA front disc rotors were sourced and fitted along with some Bendix 4wd disc pads for as new brakes again.

Brake Repair Newcastle Toronto. The Hyundai i30 required some front brakes as they were low and almost worn out which were squealing and shuddering. This is quite common towards the end of the brake pad life. New Bendix GCT Disc Pads were installed and new Disc Rotors also as they were worn out and under minimum tolerance. In most cases Disc Machining is carried out as its a cost saving for the same result. 

The mobile workshop visited Wallsend to carry out a front brake repair on an Audi A5 AWD which consisted of renewing the front disc rotors, disc pads and sensor. The disc rotors were badly grooved and unable to be machined so a better quality rotor was selected that will enable me to machine them when the brake pads wear out next time to save money.

Today I carried out some brake repairs Newcastle to the rear of a VW Golf at Adamstown NSW.

The rear brake pads Newcastle and disc rotors were worn out and metal on metal so had to be replaced and full assembly serviced.

The Hyundai i30 had a brake shudder at speed so a front disc machine was required to correct this fault, the disc pads were quite low as well so these were replaced also with a Bendix pad at Belmont NSW.

Mobile Caravan Registration Inspections. Newcastle. Lake Macquarie. Belmont.

A typical Rear Brake Repair that Newcastle Mobile Brake Specialists can do for you. I come to you and do the repairs personally. This one consisted of replacing the rear brake pads, servicing the brake caliper and anti squeal assembly, adjusting the hand brake and machining the brake disc rotors for an all factory new brake again.

HSV Senator Brakes were required, Bendix and RDA options were sourced for a cost effective and cleaner option.

Seem to be doing quite a few brake upgrades on the latest Toyota Hilux. It's usually due to the extra load with tools on the tradies ute or towing a caravan. So new quality rotors are sourced or disc machining and some heavy duty compound disc pads fitted for as new brakes again! Newcastle. Belmont. Charlestown. 

As the brake disc rotors are a friction surface they almost always require replacing or machining to true back up again. The Ford Ranger was no exception and received a front disc rotor machine and some Bendix Heavy Duty pads to accommodate for the extra weight and load when towing.